HP HPE6-A47 Exam Dumps - Actual Questions Answers

 A collision domain is a logical area of the network where devices share the same wireless medium and may interfere with each other’s transmissions. In a WLAN, a collision domain is defined by the channel and the coverage area of an AP or a client. Devices that operate on the same channel and are within range of each other belong to the same collision domain and must contend for access to the medium using the Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) protocol. Devices that operate on different channels or are out of range of each other belong to different collision domains and do not interfere with each other.

In this scenario, the architect plans 12 APs for an auditorium that is 325 square meters (3,498 square feet). Each AP has one 2.4 GHz radio and one 5 GHz radio. Both types of radios use 20 MHz channels. Assuming that DFS channels can be used in this design, the question is how many 5 GHz collision domains does this design provide.

To answer this question, we need to consider the following factors:

• The number of available 5 GHz channels in the regulatory domain of the auditorium. Different countries have different regulations on the use of the 5 GHz band, which affects the number and availability of channels for WLANs. For example, in the United States, there are 25 non-overlapping 20 MHz channels in the 5 GHz band, but some of them are subject to Dynamic Frequency Selection (DFS) requirements, which means that they must avoid interfering with radar systems by detecting and switching to another channel if radar signals are present. In other countries, such as Japan, there are 19 non-overlapping 20 MHz channels in the 5 GHz band, but some of them are restricted to indoor use only. Therefore, the number of available 5 GHz channels for the design depends on the regulatory domain of the auditorium.
• The channel assignment and distribution of the 12 APs in the auditorium. The channel assignment and distribution of the APs affect the number and size of the collision domains in the WLAN. Ideally, the APs should be assigned to non-overlapping channels and distributed evenly across the auditorium to provide optimal coverage and capacity, while minimizing co-channelinterference and adjacent channel interference. Co-channel interference occurs when devices on the same channel interfere with each other, while adjacent channel interference occurs when devices on nearby channels interfere with each other. Both types of interference degrade the performance and quality of the WLAN. Therefore, the channel assignment and distribution of the APs should follow the best practices of RF design, such as using a channel reuse plan, avoiding channel overlap, and adjusting the transmit power and antenna gain of the APs to match the coverage and capacity requirements of the auditorium.
• The coverage and capacity requirements of the auditorium. The coverage and capacity requirements of the auditorium affect the number and placement of the APs and the transmit power and antenna gain settings of the radios. The coverage requirement refers to the minimum signal strength and signal-to-noise ratio (SNR) that the APs and clients need to maintain a reliable wireless connection. The capacity requirement refers to the maximum number of clients and the minimum throughput and quality of service (QoS) that the APs and clients need to support the applications and services of the auditorium. The coverage and capacity requirements of the auditorium depend on the size and shape of the space, the density and distribution of the clients, the types and characteristics of the applications and services, and the performance and capabilities of the devices. Therefore, the coverage and capacity requirements of the auditorium should be determined by conducting a site survey and a network analysis, and then used to guide the design and configuration of the APs and radios.

Based on these factors, we can estimate the number of 5 GHz collision domains in the design as follows:

• Assuming that the auditorium is located in the United States and that DFS channels can be used in the design, there are 25 non-overlapping 20 MHz channels in the 5 GHz band. However, not all of them may be available or suitable for the design, depending on the presence and activity of radar systems in the area, the compatibility and support of the APs and clients, and the interference and noise level of the environment. Therefore, we will use a conservative estimate of 15 available 20 MHz channels in the 5 GHz band for the design.
• Assuming that the 12 APs are assigned to non-overlapping channels and distributed evenly across the auditorium, each AP will have its own 5 GHz collision domain, as there will be no co-channel interference or adjacent channel interference among the APs. Therefore, there will be 12 5 GHz collision domains in the design, corresponding to the 12 APs.
• Assuming that the coverage and capacity requirements of the auditorium are moderate and that the transmit power and antenna gain settings of the radios are adjusted accordingly, each AP will cover an area of about 27 square meters (290 square feet), which is roughly the size of a small classroom. This means that the APs will provide adequate signal strength and SNR for the clients, while avoiding excessive overlap and interference among the APs. Therefore, there will be no need to further divide or merge the 5 GHz collision domains in the design, as they will match the coverage and capacity requirements of the auditorium.

Hence, the number of 5 GHz collision domains in the design is 12, which is the answer option C. References:

• RF Design | Validated Solution Guide - Aruba
• Configuring 2.4 Ghz and 5 Ghz Radios - Aruba
• Chapter T-5: Understanding RF Collision Domains - Aruba
• [Aruba Certified Design Professional Official Certification Study Guide (HPE6-A47)]

The customer needs to upgrade their wireless network, which has a single large building with four floors. The customer requires 30 APs on each floor, totaling 120 APs for the whole building. The customer also wants to use a MM-based architecture, and deployone Aruba 7030 MC on each floor, with the MCs combined in a cluster for seamless client failover and roaming. However, the proposed solution does not meet the customer’s requirements, because the Aruba 7030 MC does not support enough APs for the customer’s needs. Each Aruba 7030 MC can only support up to 64 APs, which means that deploying one on each floor would not be enough to support all the required APs. The architect should explain this limitation to the customer, and suggest a different solution that can support more APs, such as using a higher-capacity MC model, or deploying more MCs per floor.

References:

• Aruba 7000 Series Mobility Controllers Data Sheet)
• ArubaOS 8.5 User Guide)
• Aruba Certified Design Professional Official Certification Study Guide (HPE6-A47))

 The number of devices used by each user is an important factor for creating the RF plan, as it affects the network capacity, bandwidth demand, and interference level. The architect should estimate the average number of devices per user and the types of applications they use, such as voice, video, or data. This will help the architect to determine the optimal number and placement of access points, the channel width and selection, the transmit power and data rates, and the radio resource management settings.

The OS used on wireless devices, whether BLE wayfinding is required, and the software version on MCs are not directly relevant for creating the RF plan, as they do not affectthe physical layer characteristics of the wireless network. However, they may have implications for other aspects of the network design, such as security, compatibility, and features.

References:

• RF Design | Validated Solution Guide - Aruba
• Enterprise Mobility 8.5 Design Guide - WLAN RF Design Considerations [Cisco 5500 Series Wireless Controllers] - Cisco