150-820 Brocade Certified Ethernet Fabric Professional 2015 Question and Answers

Which switch is capable of running in stand-alone mode?

You want to implement VRRP-E between a Brocade VDX 6740, and a Brocade VDX 6730 with the protocol vrrp command.

Which two statements are true? (Choose two.)

Your data center will include a Brocade VCS Fabric that has a Brocade VDX 8770-4 for access/aggregation and a VDX 8770-8 at the core. You must ensure that both chassis are assembled for highest availability. You have a total of four SFMs to deploy in the two chassis.

Which slot combinations provide the expected results?

Which feature simplifies deployment of QoS for IP-based storage in a Brocade VCS Fabric?

According to Brocade best practices, which management utility should be used in a Brocade VCS Fabric?

Your customer wants their Brocade VCS Fabric to participate in a loop-free network when connecting to other switches.

Which three protocols are supported? (Choose three.)

Which extension to the TRILL protocol allows a Brocade VCS Fabric to scale beyond 4096 VLANs?

Which two protocols are used to forward L2 traffic within a Brocade VCS Fabric? (Choose two.)

During a network outage, several RBridges in VCS Logical Chassis mode were disconnected from the rest of the network. During this time, some configuration changes were made to those switches.

When the network connection between the separated switches is repaired, what will occur?

In NOS 3.x and later, how many maximum ISLs can exist in a trunk group between a Brocade VDX 8710 and a Brocade Mi10K in a Brocade VCS Fabric?

You want to determine which link aggregation mode you should choose between a pair of Brocade VDX switches in different VCS Fabrics. You want to use frame-based distribution.

Which action should you perform?

Exhibit:

RB10# show mac-address-table port-profile

VlanId Mac-address Type State AMPP Ports

100 0050.65bf.0001 Dynamic Active Profiled (T) 2/0/1

100 0050.65bf.0002 Dynamic Active Profiled (UC) 2/0/1

Exhibit:

Referring to the exhibit, what would you determine about this interface?

You have three Brocade VCS Fabrics linked together and have enabled ELD.

Referring to the exhibit, which link would be blocked?

What are two valid ways to transfer firmware to a Brocade VDX when you perform a firmware upgrade? (Choose two.)

Which three parameters would be configured in an AMPP port profile? (Choose three.)

You want to form a single link aggregation group between a third-party switch and multiple Brocade VDX switches.

Which two conditions must be met? (Choose two.)

For direct attached active optical cables, which two distances are supported on Brocade VDX products? (Choose two.)

You want to enable a Service Virtual Fabric to provide 802.1Q VLAN virtualization.

Which two statements are correct? (Choose two.)

Your current VCS fabric comprised of Brocade VDX 8770s is running NOS 4.0.0b in logical chassis mode. You would like to upgrade the firmware with no impact to L2 traffic.

Which two procedures would accomplish this task? (Choose two.)

You are connecting your Brocade VCS Fabric to a native Brocade Fibre Channel Router (FCR) using FC ports on one of your Brocade VDX switches.

Which two port types are supported? (Choose two.)

You are required to deploy servers with a single adapter that are attached to your Brocade VCS Fabric to communicate with FC SAN attached storage.

What is required?

A customer wants to connect a group of servers to different Brocade VDXs in a three switch Brocade VDX 6740 fabric. All servers should have one gateway and should failover if one switch is taken offline for maintenance. The individual VDX should forward all packets to the destination from the VDX that receives them.

How should this solution be implemented?

You have configured your Brocade VCS Fabric to connect to a third-party switch using multiple links from two RBridges in your fabric. From the fabric, you configure a static vLAG for these links. You then receive complaints about network performance and notice a significant CPU load on the third-party switch.

What is the problem?

You have two Brocade VDX 6740 switches with cables connected in ports 15-18 and ports 31-34 in each switch to form ISLs between them.

How many trunks will form?